Jlg 1230ES Service Manual Manuel d'utilisateur Page 137
- Page / 198
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
SECTION 8 - DIAGNOSTIC TROUBLE CODES
3121222 – JLG Lift – 8-5
8.4 DTC CHECK TABLES
0-0 Help Comments
DTC FAULT MESSAGE DESCRIPTION CHECK
001 EVERYTHING OK The normal help message in platform
mode. Displays on the analyzer only.
002 GROUND MODE OK The normal help message in ground
mode. Displays on the analyzer only.
003 ALARM SOUNDING - TILTED
& ABOVE ELEVATION
Control system senses that the platform
is elevated and the vehicle is tilted, and
the machine not configured to cutout.
• Check that the machine is tilted. If so, lower the platform and
reposition the machine to a level surface.
• Fully stow the platform.
• The tilt sensor is part of the ground control box. Check that the
ground control box is secured to the machine.
• Check that the pothole protection switches are securely mounted.
• Check that the elevation angle sensor is securely mounted.
• Check the ANALYZER -> MACHINE SETUP -> MARKET configu-
ration.
• If MARKET is set to CE, ensure ANALYZER -> MACHINE SETUP -
> TILT CUTOUT parameter is set as desired.
• Backprobing ground board J1-18 should show about 0 volts.
• Backprobing ground board J1-10 should show about 0 volts.
• Check pothole protection switch adjustment.
• Calibrate the elevation sensor, see Section 5.5.
• Calibrate the tilt sensor, see Section 5.2.
004 DRIVING AT CUTBACK -
ABOVE ELEVATION
The platform is elevated and the machine
is driving.
• Fully stow the platform.
• Check that the elevation angle sensor is securely mounted.
• Check that the pothole protection switches are securely mounted.
• Check the lift/drive switch.
• Backprobing ground board J1-18 should show about 0 volts.
• Backprobing ground board J1-10 should show about 0 volts.
• Check function of elevation angle sensor. ANALYZER -> DIAG-
NOSTICS -> ELEV SENSOR -> ZEROED should be about 0V
when stowed and about 0.15V at cutback.
005 DRIVE & LIFT UP PRE-
VENTED - TILTED & ELE-
VATED
Driving is not possible since the platform
is elevated and the chassis is not level.
• Check that the machine is tilted. If so, lower the platform and
reposition the machine to a level surface.
• Fully stow the platform.
• The tilt sensor is part of the ground control box. Check that the
ground control box is secured to the machine.
• Check that the pothole protection switches are securely mounted.
• Check that the elevation angle sensor is securely mounted.
• Check the ANALYZER -> MACHINE SETUP -> MARKET configu-
ration.
• If MARKET is set to CE, ensure ANALYZER -> MACHINE SETUP -
> TILT CUTOUT parameter is set as desired.
• Check pothole protection switch adjustment.
• Backprobing ground board J1-18 should show about 0 volts.
• Backprobing ground board J1-10 should show about 0 volts.
• Calibrate the elevation sensor, see Section 5.5.
• Calibrate the tilt sensor, see Section 5.2.
- Model(s) 1
- A. GENERAL 3
- B. HYDRAULIC SYSTEM SAFETY 3
- C. MAINTENANCE 3
- REVISION LOG 4
- LIST OF FIGURES 10
- TABLE OF CONTENTS 11
- LIST OF TABLES 12
- 3121222 – JLG Lift – 1-1 13
- 1.1 OPERATING SPECIFICATIONS 14
- 1.2 LUBRICATION 14
- 1.3 CYLINDER SPECIFICATIONS 15
- 1.4 TORQUE REQUIREMENTS 15
- 1.5 SERIAL NUMBER LOCATIONS 15
- 1-4 – JLG Lift – 3121222 16
- 3121222 – JLG Lift – 1-5 17
- SOCKET HEAD CAP SCREWS 18
- 1-8 – JLG Lift – 3121222 20
- 3121222 – JLG Lift – 1-9 21
- Magni Coating (Ref 4150701)* 22
- AND MAINTENANCE 23
- INSPECTION SCHEDULE 24
- 3121222 – JLG Lift – 2-3 25
- Footnotes: 26
- GUIDELINES 27
- 2.4 LUBRICATION INFORMATION 28
- Lubrication Specifications 29
- Hydraulic Oil 29
- Changing Hydraulic Oil 29
- 2-8 – JLG Lift – 3121222 30
- 3.1 OVERVIEW 31
- 3.2 MODES OF OPERATION 31
- Ground Mode 31
- Platform mode 31
- 3.3 CAN COMMUNICATIONS 31
- 3-2 – JLG Lift – 3121222 32
- Line Contactor 33
- Right Field Winding 33
- Personalities 34
- Interlocks 34
- 3.6 PUMP/LIFT/MAST 35
- 3.7 STEER 36
- SECTION 4. BASE COMPONENTS 37
- 4.2 BASE FRAME COVERS 38
- Tire Wear and Damage 39
- Wheel and Tire Replacement 39
- Wheel Installation 39
- SECTION 4 - BASE COMPONENTS 40
- 3121222 – JLG Lift – 4-5 41
- 4-6 – JLG Lift – 3121222 42
- Steer Cylinder Disassembly 43
- Steer Cylinder - Assembly 44
- Roll And Leak Testing 48
- Oil Type & Capacity 48
- Drive Motor Disassembly 51
- Drive Motor - Reassembly 53
- Main Gear Box Disassembly 54
- Input Carrier Disassembly 55
- Hub - Disassembly 56
- Spindle Disassembly 57
- Spindle Sub-Assembly 58
- Hub Sub-Assembly 60
- Input Carrier Sub-Assembly 61
- Main Gear Box Sub-Assembly 62
- Motor Assembly 64
- Common Difficulties 65
- 3121222 – JLG Lift – 4-31 67
- Pump Components 68
- Removal Procedure 72
- Motor Brush Installation 72
- 4-38 – JLG Lift – 3121222 74
- 3121222 – JLG Lift – 4-39 75
- 3121222 – JLG Lift – 5-1 77
- Main Power Contactor Relay 78
- Elevation Limit Switch 78
- Ground Alarm 78
- 3121222 – JLG Lift – 5-3 79
- 5.3 TRACTION SYSTEM 80
- 3121222 – JLG Lift – 5-5 81
- 5-6 – JLG Lift – 3121222 82
- Installation 83
- 5-8 – JLG Lift – 3121222 84
- Power Module Diagnostics 85
- 5-10 – JLG Lift – 3121222 86
- ZAPI POWER MODULE 87
- P/N - 1001092456 87
- "HEALTH" 88
- (STATUS LED) 88
- PROCEDURE 89
- 5-14 – JLG Lift – 3121222 90
- 3121222 – JLG Lift – 5-15 91
- 5-16 – JLG Lift – 3121222 92
- 3121222 – JLG Lift – 5-17 93
- 5-18 – JLG Lift – 3121222 94
- 5.8 BATTERY/BATTERY CHARGER 95
- 5-20 – JLG Lift – 3121222 96
- FAULT LED Flashing 97
- 5-22 – JLG Lift – 3121222 98
- 3121222 – JLG Lift – 5-23 99
- - INSTALLATION 100
- SECTION 6. MAST COMPONENTS 101
- INSTALLATION 102
- SECTION 6 - MAST COMPONENTS 103
- 6.6 PLATFORM ASSEMBLY 104
- Platform Installation 105
- 6.7 MAST ASSEMBLY 106
- Mast Removal 107
- Mast Disassembly 108
- Mast - Reassembly 109
- Mast Installation 110
- Procedure 112
- Mast Installation Completion 112
- Overview 113
- Hydraulic Cylinder - Assembly 117
- 7.1 ELECTRONIC CONTROL SYSTEM 119
- Using the Analyzer: 119
- Analyzer: 120
- Machine Setup 121
- ANALYZER SCREEN LAYOUT 122
- 123
- 7-6 – JLG Lift – 3121222 124
- 3121222 – JLG Lift – 7-7 125
- 7-8 – JLG Lift – 3121222 126
- 7.2 MACHINE CONFIGURATION 127
- PROGRAMMING INFORMATION 127
- 7-10 – JLG Lift – 3121222 128
- SETTINGS 129
- 7.4 TILT SENSOR CALIBRATION 130
- Calibration Failures 130
- EVALUATION 131
- 7-14 – JLG Lift – 3121222 132
- 8.1 INTRODUCTION 133
- 8.2 X-CONNECTOR REFERENCES 133
- 8.3 DTC INDEX 133
- 8-4 – JLG Lift – 3121222 136
- 8.4 DTC CHECK TABLES 137
- 0-0 Help Comments 137
- 2-1 Power-Up 138
- 2-2 Platform Controls 138
- 2-3 Ground Controls 140
- 2-5 Function Prevented 140
- 3-3 Ground Output Driver 143
- 4-2 Thermal Limit (SOA) 145
- 4-4 Battery Supply 146
- 6-6 Communication 146
- 6-7 Accessory 148
- 7-7 Electric Motor 148
- 8-1 Tilt Sensor 150
- 8-2 Platform Load Sense 150
- 9-9 Hardware 150
- 8-22 – JLG Lift – 3121222 154
- 3121222 – JLG Lift – 9-1 155
- 9-2 – JLG Lift – 3121222 156
- 3121222 – JLG Lift – 9-3 157
- Requirements: 158
- 9.3 ELECTRICAL SWITCH TESTING 159
- Basic Check 159
- Limit Switches 159
- Automatic Switches 160
- 3121222 – JLG Lift – 9-7 161
- Assembly 162
- 3121222 – JLG Lift – 9-9 163
- Disassembly 164
- Wedge Lock 164
- Service - Voltage Reading 164
- 3121222 – JLG Lift – 9-11 165
- DT/DTP Series Assembly 166
- DT/DTP Series Disassembly 166
- HD30/HDP20 Series Assembly 166
- HD30/HDP20 Series Disassembly 167
- 9.6 X-CONNECTOR REFERENCES 167
- REAR VIEW 169
- 9-16 – JLG Lift – 3121222 170
- 9.8 X-CONNECTOR ID INDEX 171
- 9-18 – JLG Lift – 3121222 172
- 3121222 – JLG Lift – 9-19 173
- 9-20 – JLG Lift – 3121222 174
- 3121222 – JLG Lift – 9-21 175
- 9-22 – JLG Lift – 3121222 176
- 3121222 – JLG Lift – 9-23 177
- 9-24 – JLG Lift – 3121222 178
- 3121222 – JLG Lift – 9-25 179
- 9-26 – JLG Lift – 3121222 180
- 3121222 – JLG Lift – 9-27 181
- 9-28 – JLG Lift – 3121222 182
- 1001114879_F-1 183
- 9-30 – JLG Lift – 3121222 184
- 1001114879_F-2 185
- 1001114879_F-3 186
- 9.11 PIN INPUT/OUTPUT TYPES 187
- 9-34 – JLG Lift – 3121222 188
- 3121222 – JLG Lift – 9-35 189
- 9-36 – JLG Lift – 3121222 190
- 3121222 – JLG Lift – 9-37 191
- 9-38 – JLG Lift – 3121222 192
- 3121222 – JLG Lift – 9-39 193
- 9-40 – JLG Lift – 3121222 194
- 3121222 – JLG Lift – 9-41 195
- 9.12 HYDRAULIC SCHEMATIC 196
- BATTERY WARNING 197
- JLG Worldwide Locations 198
Produits connexes et manuels pour Machines spéciales Jlg 1230ES Service Manual
(174 pages)
(478 pages)
(66 pages)
(118 pages)
(164 pages)
(120 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.831 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels